50mm Square Unbraked Lazy Axle Kit
$338.92 – $937.20
Here is why Couplemate make one of the best unbraked axles
- BlueScope Steel
- Quality Hubs
- Japanese Bearings
- Pre-assembled to factory specifications
- Couplemate provides a lifetime warranty against faulty craftsmanship
Shipping
50mm Square Unbraked Lazy Axle Kit
50mm square lazy axle assembly with Australian hubs and Japanese bearings. Made in Australia by our technicians in our Wynnum workshops.
Axles are factory assembled to guarantee to certify bearings and clearances are perfect before dispatch.
- 1 x 50mm Square Australian made Axle
- 2 x Australian-made Lazy Hubs with Japanese Bearings
- Japanese bearings rated from 1450kg up to 3t
- Greased with high-temperature, high-performance grease and assembled in our workshops
50mm square unbraked axle assembly is ideal for all trailers up to 3000kg when used on the farm or for agricultural purposes.
If you require a galvanised 50mm square axle, please click this link
50mm Square Lazy Axle Rating
- LM Bearings 750kg
- SL Bearings 1450kg
- Parallel bearings 1600kg
- Dexter 1.8t bearings
- 2t Alko bearings
- 2t Dexter bearings
- 3t Alko bearings
The maximum capacity of 50mm Square axles is 3t. Bearing sizes determine the axle capacity. Note: It is recommended for heavier loads on farm trailers.
The 50mm square unbraked axle assembly is your solution to axle flex from smaller axles. Axle Flex will rapidly wear your springs due to the vibration reverberating from the centre of the axle back to the spring.
Effectively, your spring is working twice as hard as it should.
Read our article about vibration fatigue
Unbraked Axle and ratings as follows
- 39mm Round Axle Kit | Unbraked Lazy Kit – 750kg
- 45mm Round Unbraked Lazy Axle Kit – 1450kg0
- 45mm Square Unbraked Lazy Axle Kit | 1450kg – 1600kg
- 60mm Round Axle 3t Unbraked Axle
- 3t x 65mm Round Lazy Axle Kit
Calculating The Correct Axle Measurements
How to calculate the face-to-face measurement.
- Measure the offset wheel. The wheel offset is the distance between the hub’s inside and the rubber’s outside.
- Add 50 mm to the offset. Alternatively, choose the distance between the rubber and the chassis.
- Multiply by 2 for both sides. Add your chassis width to the above number.
Still unsure of what measurements to take?
Check out this handy guide below:
[P] – Check material specifications. What size and profile is the axle (for example, 45mm Square)
[T] – Overall axle length (tip to tip)
[F] – Hub face-to-hub face measurement
[A] – Chassis width
[C] – Tyre clearance
[B] – Back offset
[H] – Tyre to chassis
[G] – Axle pad centres
Identifying Bearing Combinations
You will also need to identify your bearing combination, which can be done by pulling off a hub and bearings and locating the number laser engraved onto the bearing. You will require both the inner and the outer bearing numbers.
Additional information
| Weight | 60 kg |
|---|---|
| Dimensions | 240 × 30 × 30 cm |
| Stud Pattern | Ford Parallel, 2t Landcruiser 5 Stud – Al-ko, 2t Landcruiser 6 Stud – Al-ko, 3t Landcruiser 5 stud, 3t Landcruiser 6 stud, 5 Stud Landcruiser – Parallel, 5 Stud Landrover Defender 5/8 Parallel x 6.5-inch P.C.D., 6 Stud Landcruiser – Parallel, Ford (5 x 114.30mm), Holden HT (5 x 107.95mm), Holden HQ (5 x 120.65mm), Holden Commodore (5 x 120mm), Land Cruiser 6S, Land Cruiser, 5s Landcruiser (5 x 150mm), 5S Landcruiser – 5 x 14mm Studs, Nissan – 6 x 1/2 UNF Studs, Nissan – 6 x 12mm Studs, Ford F100 – 5 x 1/2 UNF Studs, 5 Stud Landrover Discovery 5/8, 5 Stud Landrover Defender |
| Face to Face Length | 1325mm, 1350mm, 1375mm, 1400mm, 1425mm, 1450mm, 1475mm, 1500mm, 1525mm, 1550mm, 1575mm, 1600mm, 1625mm, 1650mm, 1675mm, 1700mm, 1725mm, 1750mm, 1775mm, 1800mm, 1825mm, 1850mm, 1875mm, 1900mm, 1925mm, 1950mm, 1975mm, 2000mm, 2025mm, 2050mm, 2075mm, 2100mm, 2125mm, 2150mm, 2175mm, 2200mm, 2225mm, 2250mm, 2275mm, 2300mm, 2325mm, 2350mm, 2375mm |
| Beam Size | 50mm Square |
| Bearing Profile | AU 3.0t, Parallel (PLL), Light-Medium (LM), AU 2.25t |
Our Service Lifetime Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Couplemate™ is a manufacturer and vendor of high-quality towing, trailer, and caravan components. Couplemate™ Core Goods and Custom Work are guaranteed to be free of defects for the service lifetime of the product when used as intended.
Warranties are non-transferrable and Couplemate™ requires satisfactory proof of purchase prior to issuing a remedy. The full Couplemate™ Warranty Policy can be found in the Terms & Conditions: Section 8 – Consumer Guarantees & Warranty.
Warranties are in addition to your rights under the Australian Consumer Law. If something is wrong with your order, please contact our team.
60-Day Returns
After 60 years of experience, we know that life has its unpredictable moments.
All Couplemate™ orders (online, over the phone, or in-store) have a 60 day period for change-of-mind returns and exchanges. There are some items that can’t be returned and some returns may incur a 15% restocking fee.
You can view our full policy for change-of-mind returns here.
Related products
-
45mm – 50mm Square Overlay Axle
$308.00 – $365.48 Options This product has multiple variants. The options may be chosen on the product page -
45mm Square Galvanised Hydraulic Disc Brake Axle
$1,108.00 – $1,478.00 Select options This product has multiple variants. The options may be chosen on the product page -
50mm Square 10-Inch Electric Brake Axle Kit
$644.90 – $1,028.00 Select options This product has multiple variants. The options may be chosen on the product page -
45mm Square Mechanical Galvanised Disc Brake
$714.95 – $1,434.00 Select options This product has multiple variants. The options may be chosen on the product page
Reviews